Access Control Kit 6 is a key fob access control system with fail secure lock release, exit button, power supply and key fob door reader for standard fob access control requirements
Access control for home, access control for office or any other access control solution required
** The fail secure lock release requires power to unlock, therefore it is not recommended for connection to a fire alarm as continued power to the lock release will cause irreparable damage to the lock release coil. Connection to a fire alarm would require a fail open lock release accompanied with a green emergency break switch which are an optional choice available when ordering this access control system
Both fail secure & fail safe lock releases are compatible with a typical Yale or similar rim or mortice latch which you will require. They are not compatible with a deadlock locking device
Connection drawings 
SR2-X manual Lock ReleaseLock style: Fail locked (Power required to un-lock)
12v ac/dc Coil impedance: 30 ohms
Current consumption: 760ma - 900ma
Holding force: 300kg
Supplied with: Both mortice and surface mounted face plates
Size: 160h x 25w x 31d mm
Exit buttonSurface mounted with a 2mm stainless steel facia, large exit button and Alloy surface mount back box
IP66 rated for external use
Surface mount
Changeover contacts (C/NO/NC)
Size: 85h x 85w x 42d mm
SR2-X Proximity card readerCompact, weather resistant multi-function card reader that can be used as a self-contained programmable access control card reader providing proximity entry for up to 1000 users, (987 common users, 2 panic users, 10 visitor users & 1 x Authorized user) or as a standalone Wiegand output card reader for PC based access control systems
PIN access is also possible via the remote control unit for the Administrator and all user data can be transferred from one unit to another within 3 minutes (Maximum connection is 9 units)
Main featuresManual and remote control programming
Epoxy resin filled for enhanced weather protection
ABS plastic body
IP rating: IP66, weather resistant
LED x 3 indicationColour: Black
Voltage: 9-18v DC input
Current: 40mA
Reading range: 20mm - 60mm
Card type: EM Wiegand or Mifare Classic cards and/or key fobs
Card capacity: 1,000
Relay outputs: 1 x 2amp with N.C and N.O contacts
Wiegand output: Yes
Exit button input: Yes
Fitting: Surface mount
Unit size: 103h x 48w x 20d mm
Remote control size: 85h x 32w x 5d mm
Cable tail size: 430 mm
A) All features are manual or remote programmable
B) Non-volatile memory in the event of a power failure
C) 3 x LED display indication status
Power supplyIvory white cabinet (Small)
Switch mode 13.8 volt dc regulated output 1amp power supply
Additional battery charging output
Battery deep discharge protection (Electronic)
LED Indication for mains input, DC output & battery charge/low charge
Multiple cable entry point
Size of power supply: 225h x 195w x 75d mm
Is the lock release for external use?If in direct line of rain then no, the lock connections must be concealed to avoid weather damage
Can I use the SR2-X card reader outside?Yes, it is IP66 rated and totally protected against dust and protection against heavy seas, or powerful jets of water
Will the SR2-X card reader use any standard Wiegand RFID 125Khz or Mifare Classic 13.56Mhz card or key fob?Yes it can use either
Do you program cards or key fobs via the SR2-X card reader?Yes, it's so simple to do. The SR2-X card reader is supplied with a Master Add/Delete card for this. It's also supplied with a remote control which is ideal for the deletion of lost or missing cards or fobs
NB: It is advisable to make a note of the Unique ID (U.I.D) 10 digit number printed on the cards or fobs
What happens if I lose the Master Addd/Delete card?Don't panic!, but you will need to reset the SR2-X card reader to replace it. You can use any card or key fob you like to create a new Master Add/Delete card. You will not lose any previously programmed cards or fobs by resetting the unit - The reset procedure is detailed within the online manual
How do I delete cards or key fobs if I have lost them?You can delete cards or key fobs in two ways, the first is by physically having the card or key fob and use the Master Add/Delete card, or if you have lost the card or fob, you can use the remote control by entering the U.I.D 10 digit number
Can I use two SR2-X card readers to access and exit a door?Yes if you wish, just buy an additional SR2-X
HereIf I wanted two SR2-X card readers, can I program the same card or key fob to activate both units?Yes, you can actually connect up to 9 x SR2-X's together and upload the user information from the first SR2-X to all additional SR2-X readers. Please refer to page 7 of the manual we have for download that will show you this
Can I operate my automatic gate with this?Yes, please refer to the drawings we have for download that will show you this
What cable do I need? You can use any cable you like for this, we suggest using 3 paired or 4 paired standard alarm cable that you can purchase from any local electrical or DIY store
